اطلاعیه : آخرین فرصت ثبت سفارش جهت ارسال در سال 1402, روز پنجشنبه 1402/12/24 خواهد بود. سفارشات ثبت شده پس از این تاریخ به ترتیب اولویت از6 فروردین 1403 ارسال خواهند شد.
درایور استپر موتور DRV8825 ویژه پرینتر سه بعدی درایور استپ موتور

ماژول DRV8825 یک درایور استپر موتور شامل یک برد کمکی TI DRV8825 برای راه اندازی موتورهای استپر دوقطبی بصورت میکرواستپ است. این ماژول دارای پین خروجی و اینترفیس که تقریبا برابر برد درایور استپر A4988 است که می تواند در بالاترین سطح عملکرد جایگزینی مناسب برای این برد در بسیاری از پروژه ها باشد. از ویژگی های این ماژول می توان به تنظیم محدوده جریان ،داشتن محافظ در برابر مصرف جریان اضافی و افزایش دما بیش از حد و همچنین دارای 6 میکرواستپ با تفکیک پذیری تا 1/32 استپ نام برد. این ماژول با ولتاژ 8.2 تا 45 ولت کار می کند و می تواند در هر فاز بدون هرگونه هیت سینک و جریان هوای فن حداکثر تا 1.5A جریان دهی کند.( با ایجاد خنک سازی موثر تا 2.2A). این ماژول با بردهای آردینو کاملا سازگار است.

ویژگی ها
دارای رابط کنترلی ساده برای جهت و استپ
دارای 6 حالت متفاوت تفکیک پذیری استپ: استپ کامل، نیم استپ، ¼ استپپ، 1/8 استپ، 1/8 استپ، 1/16 استپ و 1/32 استپ
کنترل قابل تنظیم جریان برای داشتن ماکزمیم جریان خروجی با استفاده از پتانسیومتر
ماکزیمم ولتاژ 45 ولت
دارای رگولاتور داخلی
قابلیت ارتباط مستقیم با ولتاژ 3.3 ولت و 5 ولت سیستم
دارای محافظ ولتاژ ، جریان و حرارت با قابلیت shutdown
 

Overview

This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet (1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section below for more information). Here are some of the driver’s key features:

Simple step and direction control interface
Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
45 V maximum supply voltage
Built-in regulator (no external logic voltage supply needed)
Can interface directly with 3.3 V and 5 V systems
Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
Short-to-ground and shorted-load protection
4-layer, 2 oz copper PCB for improved heat dissipation
Exposed solderable ground pad below the driver IC on the bottom of the PCB
Module size, pinout, and interface match those of our A4988 stepper motor driver carriers in most respects (see the bottom of this page for more information)

 

نوشتن نظر

توجه: HTML ترجمه نمی شود!
    بد           خوب

درایور استپر موتور DRV8825 ویژه پرینتر سه بعدی

  • مدل کالا: DRIVER DRV8825
  • موجودی: 25
  • 135,000تومان

برچسب ها: درایور, استپر, موتور, DRV8825, ویژه, پرینتر, بعدی, استپ